Technical Insights

Fan Curves: System Resistance and Heat Balance

Technical poster showing an axial fan and a guide to reading fan curves.

To size a cooling fan, first calculate the airflow needed to remove the heat load at the allowed air-temperature rise. Then compare the fan’s measured P-Q curve with the system resistance curve using consistent units and test conditions. Their intersection predicts the installed airflow; a free-air CFM rating alone does not. Verify the selected operating point and component temperatures in the assembled equipment.

This guide explains how to read fan curves correctly, how to construct a system impedance curve, how to find the operating point, and what to do when your initial selection does not meet your cooling target.

What a Fan Curve Actually Shows

A fan’s P-Q (Pressure-Volume) curve plots the relationship between:

  • X-axis: Volumetric airflow (CFM or m³/h)
  • Y-axis: Static pressure developed by the fan (Pa or inH₂O)

At zero flow, read the shutoff static pressure. A stall region can occur elsewhere on the curve; it is not another name for this endpoint. Neither shutoff nor a manufacturer-identified unstable region is a suitable cooling duty point.

At the right end (zero pressure), the fan moves its maximum volume of air—but develops no pressure. This is the free delivery point, also called free air flow or open flow.

Every real installation falls somewhere between these extremes. The fan must develop enough pressure to overcome the system resistance while delivering the required airflow.

Read input power or current from the selected fan’s data at the intended duty point and across the expected operating range. The power-curve shape varies with fan design; there is no universal 50–70% airflow rule or universal free-delivery overload condition. AMCA explains the different curve shapes.

Constructing a System Impedance Curve

The system impedance curve describes how much pressure drop your cooling system creates at various flow rates. For a fixed airflow path in a predominantly turbulent regime, a useful approximation is:

ΔP_system = k × Q²

Where:

  • ΔP_system = system pressure drop (Pa or inH₂O)
  • k = system resistance coefficient (determined by testing or calculation)
  • Q = volumetric flow rate

To construct the curve, you need the pressure drop of each component in the airflow path:

Check each part of the airflow path: inlet and exhaust filters, guards, heatsinks, PCB guides and cable obstructions. Use pressure-loss data at the required flow and filter service condition; these parts do not have universal pressure-drop values. Measure the assembled enclosure if reliable component data are unavailable.

Example calculation for a 120mm filter fan installation:

For a hypothetical clean-filter system, assume a measured pressure loss of 10 Pa at 100 CFM. NIST’s conversion table gives 1 CFM = 28.31685 L/min, so 100 CFM = 2.831685 m³/min. With Q in m³/min, k = 10 / (2.831685)² ≈ 1.2471 Pa/(m³/min)². Keep these units throughout the calculation.

To construct the system curve, calculate ΔP at multiple flow rates:

Calculated pressure loss for the hypothetical 10 Pa at 100 CFM system
Flow (m³/min) System pressure loss (Pa)
0.5 0.31
1.0 1.25
1.5 2.81
1.7 3.60
2.0 4.99
2.5 7.79
2.8317 (reference point) 10.00

Plot this curve on the same graph as the fan’s P-Q curve. The intersection is the operating point.

Reading the Operating Point

Case 1: Adequate airflow margin

If the predicted operating point meets the required airflow, the fan is a candidate for enclosure testing, not a confirmed fit. Set the design margin from the measured dirty-filter condition, leakage or recirculation, production tolerances and actual air density. Verify component temperatures at the worst intended operating conditions.

Case 2: Insufficient airflow at operating point

Options:

  1. Select a fan with higher static pressure at the required flow rate — not necessarily higher free-air flow
  2. Reduce system resistance by using a coarser filter media, enlarging inlet/outlet apertures, or removing flow obstructions
  3. Use two fans in series — assess the combined pressure curve when system resistance is the constraint
  4. Use two fans in parallel — assess the combined airflow curve when more volume is needed

Series vs. parallel configuration:

Ideal curve addition for two identical fans; installed performance requires verification
Configuration Ideal combined curve Selection check
Series Add pressure at equal flow Check the new intersection with a high-resistance system
Parallel Add flow at equal pressure Check flow sharing and the new system operating point

These are ideal combined curves, not a promise to double the installed flow. Fan spacing, inlet conditions, unstable operation and system resistance affect the result. See ASHRAE’s discussion of multiple-fan operation.

Choose the arrangement by comparing the combined fan curve with the actual enclosure curve; cabinet size or a short air path alone does not establish which arrangement is better.

The Fan Curve in Practice: A Hypothetical Charger Heat-Balance Check

Example assumptions: 8,000 W must be removed by the ventilation air, and a 15 K bulk-air temperature rise is allowed. This is a calculation example, not an SXDOOL equipment test. For this reference calculation only, take air density ρ = 1.2 kg/m³ and specific heat cp = 1,005 J/(kg·K).

Q = 60 × heat load / (ρ × cp × temperature rise)
  = 60 × 8000 / (1.2 × 1005 × 15)
  ≈ 26.5 m³/min

At the same assumptions, 12 m³/min carries only about 3.62 kW. The heat-balance method relates air mass flow to heat load and temperature rise; see Oriental Motor’s worked selection example. The calculated 26.5 m³/min is an airflow requirement, not a fan’s free-air rating or proof of equipment compliance.

A 40°C ambient limit and a 55°C internal limit do not by themselves prove a usable 15 K bulk-air rise. Use actual inlet conditions and component limits. Recalculate density for the design temperature and altitude, and identify any heat removed through the enclosure or another cooling circuit.

If a separate hypothetical system loses 12 Pa at 12 m³/min, its square-law coefficient is 12/12² = 0.08333 Pa/(m³/min)². At the calculated 26.53 m³/min requirement, that approximation gives about 58.7 Pa. Confirm the approximation over this range before using it.

To select a fan, obtain a measured curve for the exact voltage, speed and build and find its intersection with the system curve. Free-airflow and shutoff-pressure endpoints alone cannot establish an operating point, a speed setting, a noise reduction or thermal compliance. Ask SXDOOL to check the selected model against these conditions before sample testing.

Common Fan Curve Mistakes and How to Avoid Them

Mistake 1: Selecting based on free-air CFM
A fan with 300 CFM free-air flow may deliver only 180 CFM in your system. Always find the operating point on the P-Q curve.

Mistake 2: Ignoring filter pressure drop
Use the selected filter’s flow-versus-pressure data in clean and specified service conditions. Include guards and the installed enclosure; an arbitrary allowance in Pa is not a substitute for these data.

Mistake 3: Ignoring air density
At the same volume flow, lower-density air carries less mass and less sensible heat for a given temperature rise. Use the actual temperature and atmospheric-pressure conditions for the heat balance, and check the reference density stated on the fan curve.

Mistake 4: Selecting an unstable operating region
Use the manufacturer’s recommended stable range for the exact fan and test the installed assembly for noise and vibration. Do not assume every left-hand point is stalled or that every fan has the same unstable range.

Mistake 5: Assuming ideal fan-array performance
Check the installed fan spacing, shared plenum, flow sharing and any required fan-out condition. Parallel fans do not automatically deliver twice the single-fan installed airflow.

Requesting P-Q Data from SXDOOL

When requesting data from SXDOOL, identify the complete model and revision, voltage, control signal, installation and target duty point. Confirm which measured P-Q data and test conditions are available for that exact build before treating it as a candidate for your equipment.

Data to request:

  • P-Q curves with voltage, speed, air density and test setup
  • Input current or power across the intended operating range
  • Control-signal definition and curves at the intended speeds, where available
  • Noise results with measurement distance, setup and operating condition

Contact our engineering team: david@sxdool.com
Visit www.sxdool.com | WhatsApp: +86 134 3209 3474

Confirm sample availability, quantity and shipment timing in the quotation for the selected build.

For a shorter introduction to the chart axes, see Understanding Fan Curves.

From the Calculation to a Fan Candidate

When using the SXDOOL fan selector, have your electrical supply and installation constraints ready. For a changed cable, connector or control requirement, describe it through the custom cooling fan enquiry page. Include the required airflow at pressure, heat load, inlet conditions and enclosure restrictions. A family match is only a starting point; confirm the measured curve for the exact build before sample testing.

Leave a Reply

Your email address will not be published. Required fields are marked *